Arlington's mix of established mid-century neighborhoods and newer master-planned communities like Viridian gives the city one of the widest ranges of roofing needs in the Mid-Cities. Tarrant County storm exposure hits North and South Arlington alike, and with the city's older housing stock aging past its original shingle life expectancy, more homeowners are opting to replace once and be done rather than reroof with asphalt every 12 to 15 years.
The Case for Metal Roofing
in Arlington
In a North Texas hail zone with home values like Arlington's, asphalt shingles are an expensive recurring cost — not a long-term solution.
Figures represent accepted industry ranges but will vary by home, carrier, and installation. Individual results will vary, and actual savings are not guaranteed. Consult a local real estate professional for market-specific figures and your insurance and utility providers for personalized savings. The ROI calculation is based on 20-yr cost comparison of avoided replacement, insurance and energy savings vs. upfront investment.
With a 2% wind/hail deductible and Arlington's home values, a single claim means a five-figure out-of-pocket expense — often approaching or exceeding the full cost of a cash roof replacement. And that resets every 8–10 years.
A metal roof eliminates the replacement cycle entirely. Add carrier discounts, reduced energy costs, and eliminated deductible exposure over 20–30 years — and the upgrade typically pays for itself well within the life of the home. Metal roofs typically recoup 50–60% of installation cost at resale — and unlike asphalt, that return doesn't reset every 8–10 years with a full replacement, per Remodeling magazine's Cost vs. Value report.
Metal & Synthetic Slate
for Arlington Homes
Roofing Costs in Arlington, TX
Installed cost by material, based on current DFW-wide market rates. Arlington homeowners typically fall within these ranges regardless of neighborhood -- your exact number depends on your roof's size, pitch, and complexity, not just your zip code.
| Material | $ / Sq Ft Installed | Est. Total (3,500 Sq Ft Roof) |
|---|---|---|
| R-Panel / Exposed-Fastener Steel | $7–$11 | $24,500–$38,500 |
| Stone-Coated Steel | $10–$16 | $35,000–$56,000 |
| Standing Seam Steel | $12–$18 | $42,000–$63,000 |
| Premium 24-Gauge Standing Seam | $15–$22+ | $52,500–$77,000+ |
| Synthetic Slate (Composite) | $12–$20 | $42,000–$70,000 |
| Copper | $25–$40+ | $87,500–$140,000+ |
DFW-wide installed-cost ranges as of 2026, for material and labor combined. Sample totals assume a 3,500sq ft roof with typical pitch and access — actual cost depends on your roof's exact size, slope, tear-off needs, and site conditions. Get a free satellite-based estimate for your home's specific number.
DFW Installations
Areas We Serve in Arlington
From Visualization to Installation
Precision Proposal
Using your assessment findings and satellite measurements, we build your firm proposal — one clear number, presented in person, with no post-signing surprises.
Expert Installation
Your roof is installed to manufacturer spec by a credentialed metal roofing specialist — licensed in Texas and fully insured — and covered by our 10-year workmanship warranty from day one.
The 40-Point Roof
& Structure Assessment
Before we build your Arlington proposal, we inspect structure, weatherproofing, ventilation, and every penetration — 40 points in all. It's the same diagnostic professional inspectors charge for, done free with every estimate, so your price is locked before installation day, not renegotiated after.
Decking integrity, rafter/truss condition, slope verification, load capacity for your chosen system.
Valley, chimney, and skylight flashing, drip edge, step flashing, pipe boots, sealant condition.
Ridge and soffit vent function, attic moisture and insulation, airflow balance.
Solar mounts, satellite brackets, HVAC lines, electrical mast, plumbing vents, skylights.
Gutters, downspouts, fascia, soffits, roof-to-wall transitions, ponding risk.
Satellite aerial measurement, wind/hail rating compliance, HOA material review, permitting.
One Project Lead. One Warranty. Zero Chasing.
Metal Roofing Questions —
Arlington, TX
What warranty comes with a metal roof in Arlington, TX?
Every roof we install is covered by a 10-year workmanship warranty, written into your contract — plus the manufacturer's material warranty on the panels and finish. Combined with a 50+ year system lifespan, that means coverage most Arlington homeowners will never need to use.
How much does a metal roof cost in Arlington?
Metal roofing in Arlington typically ranges from $16,000 to $60,000 depending on roof size, pitch, and material. We provide a satellite-based ballpark range from your roof's measured size — not a guess from the driveway — refined into a firm number after your free on-site assessment. By material, that typically breaks down to about $7–$11/sq ft for R-panel, $10–$16/sq ft for stone-coated steel, $12–$18/sq ft for standing seam, and $15–$22+/sq ft for premium 24-gauge standing seam — see our full pricing table above for a size-based cost breakdown.
Is metal roofing common in newer Arlington developments like Viridian?
Yes. Viridian's architectural guidelines already permit metal roofing in approved profiles, and it's an increasingly common choice among homeowners building or reroofing in the community given the neighborhood's exposure to the same Tarrant County hail corridor as the rest of Arlington.
Does a metal roof qualify for an insurance discount in Arlington?
Yes. Class 4 impact-rated metal roofing qualifies for significant premium discounts from most Texas carriers. Arlington sits in an active hail corridor between Fort Worth and Dallas, and homeowners who upgrade typically see a meaningful reduction in their wind/hail premium.
Will my Arlington HOA approve a metal roof?
Communities with an active architectural review process, like Viridian, generally approve metal roofing in pre-approved profiles and colors. Many older Arlington neighborhoods have no HOA at all. Where documentation is required, we provide material samples, color chips, and manufacturer spec sheets at no additional cost.
How long does metal roof installation take in Arlington?
Most residential installations in Arlington are completed in one to three days. The exact timeline depends on roof size and material selection — we provide a specific estimate timeline for your home before any work begins.
What metal roofing styles work best for Arlington homes?
Standing seam suits the more contemporary builds going up in Viridian and other newer developments, while stone-coated steel is a strong match for the traditional ranch and mid-century homes common across North and South Arlington. Both carry Class 4 hail ratings and 50-plus year lifespans.
Still have a question? Text ROOF to (817) 382-3338.
Metroplex Metal Roofs specializes in premium residential roofing across the Dallas–Fort Worth metroplex, led by metal and complemented by synthetic slate. Our focus is standing seam, stone-coated steel, copper, and R-panel — every project precision-measured by satellite, installed to manufacturer spec, and backed by our 10-year workmanship warranty.
Learn About Our Approach →The Last Roof You'll Ever Put
On Your Arlington Home
See your home with a metal roof before you commit to anything. Satellite-based estimate. No obligation.